Shipping BYD Body Kits to Brazil: ABS Packaging & Freight Guide

If you import body kits, the short answer is: each part ships in its own box with surface protection and reinforced corners, and freight must be calculated by volume (CBM), not by weight. An ABS body kit is light and bulky at the same time — getting the freight basis wrong is the most common cause of a surprise cost on arrival. This guide shows how the packaging is done, how to calculate freight correctly and what to check on receipt.

How each part is packed

A full body kit has 4 to 6 parts, and each has its own geometry — a rear bumper is a large, curved part, a side skirt is long and thin, and a rear wing has a broad, fragile surface. The packaging is designed part by part:

PartBox shapeMain protection
Front bumperLarge box shaped to the curveCorner foam + surface-protection film
Rear bumperLarge shaped boxCorner foam + surface film
Side skirtLong, narrow boxIntermediate wrapping + edge protection
Rear wingFlat, wide boxRigid support against deformation
Rear diffuserMedium boxCorner foam

Surface protection is mandatory: the part arrives covered in a film that prevents scuff marks. Ask your customs broker and carrier not to remove the film before inspection. A body kit is painted later, and the final finish depends on that layer staying intact all the way to the body shop.

Volume: the correct basis for freight

For body kits, CBM (volume) is what drives the freight cost, not weight. A rear bumper box can weigh under 10 kg yet take up 0.4 m³ — if you quote by weight, the real shipment cost will be far higher than expected.

To do the maths you need three numbers the factory supplies with the quote:

With those three numbers any forwarder can quote the freight accurately. Ask for this data before you close the order with your customs broker, and never use another supplier's quote as a volume reference — every factory packs differently.

Air or sea

ModeTransit timeWhen to use it
Air15 to 25 days door-to-doorFirst shipment, test batch, fast restock
Sea40 to 55 days door-to-doorRepeat orders from around 500 kits upward

Sea freight is the right route for body kits. High volume and low weight is exactly the profile that makes sea freight pay. The break-even sits around 500 kits for most part combinations. Before that, while the market is still being tested, air freight preserves cash flow.

Carton boxes or wooden crates?

For large volumes, a wooden crate is usually better than stacked cartons, because:

For smaller batches, reinforced cartons with corner protection are enough and cheaper. Ask for the packaging recommendation together with the quote — the factory knows which combination is safest for each route.

How to check the delivery

The container arrived and the kit does not match what you expected? Here is the order of action that prevents trouble:

  1. Photograph before opening — record the condition of the boxes and the seal on arrival.
  2. Check the number of boxes against the packing list, before opening anything.
  3. Open and inspect part by part — check against the batch dimensional checklist.
  4. Do not remove the surface protection until the inspection is complete.
  5. Record any damage in writing before signing the carrier's receipt — damage not logged on the spot is damage with no cover.

Ruiton includes a dimensional checklist per batch, which makes the check objective and quick. If you need it, also ask for photos of the inspection process before shipment.

Documentation for customs clearance

For the full view of the buying process, see how to become a body kit distributor.

For body kits, the customs classification is what most often holds up release. Have these in hand before shipment:

The description on the invoice is decisive. A generic "auto parts" raises questions at customs and causes delays. Describe the part as it is: sporty front bumper in ABS for a specific vehicle. Ask the factory for the technical data sheet you should use in the description.

Frequently asked questions

How does the body kit arrive undamaged?

Each part ships in its own box, with corner foam and surface-protection film. For large volumes, a wooden crate is safer than stacked boxes. Requesting an inspection on arrival, with a photo before opening, is what protects your operation.

What is the volume per full kit?

It depends on the composition. A kit with front and rear bumpers, side skirts and a rear wing typically takes between 0.5 and 0.9 m³ per set. The exact figure comes in the quote, by composition.

Is sea freight worth it for body kits?

Yes, from around 500 kits. The body kit profile — light and bulky — is exactly the case where sea wins. Before that, air preserves cash flow and brings product validation forward.

Can I receive it in parts?

Yes. The order can be split into shipments by model or by part, which helps align stock with real demand. Each shipment has its own packing list and tracking.

Do you handle customs clearance?

We work mainly FOB or CIF. We can introduce your broker at shipment and send all the documentation. Clearance in the buyer's name stays with your broker in Brazil.

Do you issue an invoice and a technical data sheet?

Yes, the commercial documents and the technical data sheet come with the shipment. Specific compliance reports are confirmed on request — ask in the quote, stating the country and application.

Next step

Tell us the models, the part composition you want, the quantity and the destination. The team replies with FOB and CIF quotes, volume per kit and the packaging recommendation for your route.

Note: the values, lead times and MOQ in this guide are Ruiton line references and may vary by model, kit composition and batch. Specific test reports (RoHS/REACH) are provided on request.

Browse parts by model  

Other categories

Products in this line

Related guides